Goseeko blog
  • Home
  • Engineering
    • Civil
    • Electronics
    • Computers
  • Science
    • Chemistry
    • Maths
    • Physics
  • Commerce
  • Arts
  • E-Learning
  • Career
  • Exams
  • Scholarships
  • Hiring News
  • Goseeko- Smart Study Material
@2021 - All Right Reserved. Designed and Developed by PenciDesign
Top Posts
Goseeko launches its own certifications for engineering and...
Online certifications which you can get in a...
What is Race around Condition?
What is a Development Plan ?
What is a Co-operative Bank?
What are the properties of Laser?
Top 5 Websites for Academic Research
What is regula-falsi method?
Top 10 Engineering YouTube Channels for Engineers
What is Lorentz Transformation?
What are Toposheets?
What is Pumping and its types?
Civil

What is Well Foundation?

by Swati 30/10/2021
written by Swati 30/10/2021 0 comment
Well Foundation
  • Well foundation is a type of deep foundation which generally provided for construction of bridges.
  • The art of well foundation is well known to Indians, since world famous “Taj mahal” stands on well foundation.

Advantages of Well foundation:

  1. It can with stand large lateral forces as in case of piers, alignments, tall chimneys etc. in a better way due to rigidity and large cross section.
  2. It is possible to examine strata and decide depth of founding the well.
  3. during construction of well foundation hence, adjoining structures are not affected.

Components of Well Foundation:

Various component of well foundation are described below:

  1. Cutting edge
  2. Steining
  3. Curb
  4. Concrete seal or bottom plug
  5. Top Plug
  6. Well cap
  1. Cutting Edge:
  • The function of the cutting edge is to facilitate easy penetration or sinking into the soil to the desired depth. 
  • As it has to cut through the soil, it should be as sharp as possible, and strong enough to resist the high stresses to which it is subjected during the sinking process.
  • Hence it usually consists of an angle iron with or without an additional plate of structural steel. Sinking of well with sharp edge is fast however if strata meets with boulders, then the damage to edge may happen.
  1. Steining:
  • The steining forms the bulk of the well foundation and may be constructed with brick or stone masonry or with plain or reinforced concrete occasionally,
  • One makes the thickness of the steining uniform throughout its depth. 
  • One considers it desirable to provide vertical reinforcements to take care of the tensile stresses which might occur when one suspend the well from top during any stage of sinking.
  1. Curb:
  • The well curb is a transition member between the sharp cutting edge and the thick steining. 
  • It is thus tapering in shape. 
  • One makes it of reinforced concrete and subjects it to severe stress during the sinking process.
  1. Concrete seal or bottom plug:
  • After the well foundation is sunk to the desired depth so as to rest on a firm stratum, a thick layer of concrete is provided at the bottom inside the well, generally under water. 
  • This layer is called the concrete seal or bottom plug, which serves as the base for the well foundation.
  • The Primary aim is to distribute the loads on to a large area of the foundation, and hence may be omitted when the well is made to rest on hard rock.
  1. Top Plug:
  • After the well foundation is sunk to the desired depth, the inside of the well is filled with sand either partly or fully, and a top layer of concrete is placed. 
  • This is known as ‘top plug’.
  • The sand filling serves to distribute the load more uniformly to the base of the well, to reduce the stresses in the stening and to increase the stiffness of the well foundation.
  • However, as this adds to the weight and load transmitted to the foundation stratum, the engineer has to consider the desirability or otherwise of providing the sand filling from the port of view of bearing power and settlement.
  • Lastly, the top plug and concrete serve to transmit the loads to the base in a uniform manner.
  1. Well cap
  • The well cap serves as a bearing pad to the superstructure, which may be a pier or an abutment. 
  • It distributes the superstructure load onto the well steining uniformly.

Fig:Components of well foundation

Interested in learning about similar topics? Here are a few hand-picked blogs for you!

  • What is Cross Drainage Work?
  • Rivers
  • What is Weir?
  • What is Spillway?
  • Arch dams
Share
0
FacebookTwitterPinterestLinkedinTumblr
previous post
List of The Top 10 B.Com Colleges across India
next post
What is method of variation of parameters?

You may also like

What is Ventilation?

30/10/2021

Types of Survey in Civil Engineering

30/10/2021

What is Evaporation ?

30/10/2021

What is Cofferdam?

30/10/2021

What is Caissons?

30/10/2021

Seismic Waves

30/10/2021

Under Reamed Pile

30/10/2021

What is Reaction Turbine?

30/10/2021

What is Piers?

30/10/2021

What is Workability ?

30/10/2021

Leave a Comment Cancel Reply

Save my name, email, and website in this browser for the next time I comment.

Keep in touch

Facebook Twitter Instagram Youtube

Popular Posts

  • 1

    What is Race around Condition?

    03/08/2021
  • 2

    What is a Development Plan ?

    02/08/2021
  • 3

    What is a Co-operative Bank?

    03/08/2021
  • 4

    What are the properties of Laser?

    02/07/2021
  • 5

    Top 5 Websites for Academic Research

    11/07/2021
  • 6

    What is regula-falsi method?

    03/08/2021
  • 7

    Top 10 Engineering YouTube Channels for Engineers

    10/07/2021
  • 8

    What is Lorentz Transformation?

    02/07/2021
  • 9

    What are Toposheets?

    07/07/2021
  • 10

    What is Pumping and its types?

    03/08/2021

Categories

  • Arts
  • Career
  • Chemistry
  • Civil
  • Commerce
  • Computers
  • E-Learning
  • Electronics
  • Engineering
  • Exams
  • Hiring News
  • Maths
  • Physics
  • Scholarships
  • Uncategorized

Read alsox

What is Earth dam?

31/05/2021

What is a Tender Notice?

31/05/2021

What is Shotcrete?

05/07/2021