Goseeko blog


by Paurnima janrao

What is a generator?

A generator is a system that converts to be had mechanical power into electric electricity. It works at the precept of faraday’s regulation of electromagnetic induction. Based at the output obtained, we classify turbines as:

  • ac generator
  • dc generator

Within the subsequent phase, allow us to study extra about ac generators.

Ac generator or alternators:

Ac generator, additionally known as alternators, is a system that converts mechanical strength into electric strength. The generated electric power is inside the shape of an alternating cutting-edge sinusoidal output waveform. 

The mechanical strength is usually provided by steam mills, gas generators and combustion engines.

Ac turbines paintings on the precept of faraday’s law of electromagnetic induction which states that electromotive pressure -emf or voltage – is generated in a modern-day-carrying conductor that cuts a uniform magnetic area.

 This may both be finished with the aid of rotating a carrying out coil in a static magnetic area, or through rotating the magnetic discipline that carries the desk bound conductor.

 The desired arrangement is to preserve the coil desk bound because it’s far simpler to attract precipitated alternating contemporary from a stationary armature coil than a rotating coil.

The generated emf depends at the range of armature coil turns, magnetic discipline strength, and the rate of the rotating subject.

The parts of an ac generator are:

  • field
  • armature
  • Prime mover
  • rotor
  • stator
  • slip rings

Here, we’ve said the cause of each component:

  • Field

The field consists of coils of conductors that receive a voltage from the source and convey magnetic flux. The magnetic flux inside the discipline cuts the armature to produce a voltage. This voltage is the output voltage of the ac generator.

  • Armature

The a part of an ac generator in which the voltage is produced is referred to as an armature. This thing broadly speaking consists of coils of wire that are massive sufficient to hold the entire-load cutting-edge of the generator.

  • prime mover

The factor used to power the ac generator is called a high mover. The top mover may want to both be a diesel engine, a steam turbine, or a motor.

  • Rotor

The rotating component of the generator is known as a rotor. The generator’s high mover drives the rotor.

  • Stator

The stator is the stationary part of an ac generator. The stator core is made from lamination of steel alloys or magnetic iron, to limit the eddy present day losses.

  • Slip rings

Slip rings are electrical connections which can be used to switch electricity to and fro from the rotor of an ac generator. They may be commonly designed to behavior the waft of current from a desk bound tool to a rotating one.

Workingof an ac generator:

While the armature rotates between the poles of the magnet upon an axis perpendicular to the magnetic field, the flux linkage of the armature modifications constantly. Due to this, an emf is precipitated in the armature. 

This produces an electric powered modern-day that flows thru the galvanometer and the slip jewelry and brushes. The galvanometer swings between high quality and negative values. This suggests that there is an alternating current flowing thru the galvanometer. The path of the prompted current may be diagnosed using fleming’s right hand rule.

Advantages of AC generator:

Following are some benefits of ac generator over dc generators:

  • ac turbines can be easily stepped up and stepped down through transformers.
  • Transmission hyperlink size might be thinner because of the step-up characteristic
  • losses are noticeably lesser than dc gadget
  • length of the ac turbines are fantastically smaller than dc turbines

 dc generator:

A dc generator is an electrical gadget whose fundamental feature is to convert mechanical electricity into energy. Whilst conductor slashes magnetic flux, an emf can be generated based at the electromagnetic induction principle of faraday’s laws. This electromotive force can purpose a drift of present day when the conductor circuit is closed.

parts of a dc generator:

A dc generator can also be used as a dc motor with out changing its construction. Consequently, a dc motor, in any other case a dc generator can be normally known as a dc device. Underneath we’ve mentioned the important components of a dc generator.

  • Stator

The principle feature of the stator is to offer magnetic fields wherein the coil spins. A stator consists of  magnets with contrary polarity going through each other. These magnets are positioned to in shape inside the location of the rotor.

  • Rotor

A rotor in a dc machine consists of slotted iron laminations with slots that are stacked to shape a cylindrical armature core. The characteristic of the lamination is to lower the loss induced because of eddy modern-day.

  • Armature windings

Armature windings are in a closed circuit shape and are related in collection to parallel for reinforcing the sum of produced contemporary.

  • Yoke

The outside shape of the dc generator is referred to as yoke. It’s far made of either forged iron or steel. It presents necessary mechanical energy for carrying the magnetic-flux given thru the poles.

  • Poles

The function of a pole is to preserve the field windings. These windings are wound on poles and are either related in collection or parallel through the armature windings.

  • Pole shoe

Pole shoe is especially utilized for spreading the magnetic flux to keep away from the sector coil from falling.

  • Commutator

A commutator works like a rectifier that changes ac voltage to dc voltage within the armature winding. It’s far designed with a copper section, and every copper section is covered from every other with the assist of mica sheets. It’s far positioned at the shaft of the device.

  • Brushes

The electric connections may be ensured between the commutator as well as the outdoors load circuit with the help of brushes.

Working of Dc generator:

According to faraday’s regulation of electromagnetic induction, we know that after a present day-wearing conductor is positioned in a varying magnetic subject, an emf is triggered inside the conductor. In keeping with fleming’s right-hand rule, the direction of the precipitated cutting-edge adjustments whenever the route of movement of the conductor adjustments. Allow us to remember an armature rotating clockwise and a conductor on the left moving upwards. While the armature completes a 1/2 rotation, the course of the motion of the conductor could be reversed downward. Subsequently, the course of the current in every armature will be alternating. However with a cut up ring commutator, connections of the armature conductors get reversed whilst a modern-day reversal takes place. Therefore, we get unidirectional modern on the terminals.

Tyeps of DC generator:

The DC generator can be classified into two main categories as separately excited and self-excited.

  • Separately Excited

In a separately excited type generator, the field coils are energized from an independent exterior DC source.

  • Self Excited

In a self-excited type, the field coils are energized from the generated current within the generator. These types of generators can further be classified into a series of wounds, shunt-wound, and compound wound.

Applications of DC Generators:

  • The separately excited type DC generators are used for power and lighting purposes.
  • The series DC generator is used in arc lamps for lighting, stable current generator and booster.
  • DC generators are used to reimburse the voltage drop within Feeders.
  • DC generators are used to provide a power supply for hostels, lodges, offices, etc.

You may also like