Unit 2

- Explain Kirchhoff’s current law ?

Kirchhoff Current Law:

A node is a circuit connection that extends to all its neighbouring elements but does not contain them.

Kirchhoff’s current law states that at a node:

Sum of the in currents = sum of out currents

Applying KCL at four nodes

0 = Ix + I1 + I2 KCL at node a

I2 = I3 KCL at node b

I3 + I4 = 0 KCL at node c

Ix + I1 = I4 KCL at node d

Adding equations 6-9 gives the following equation:

Ix + I1 + I2 + I3 + I4 = Ix + I1 + I2 + I3 + I4.

2. Explain Kirchhoff’s voltage law?

Kirchhoff Voltage Law:

A loop is a path around a circuit that starts and ends in the same place.

Kirchhoff's voltage law (KVL) states that around a loop:

Sum of voltage rises=sum of voltage drops--------------------(1)

Applying KVL around the three loops we get

V1 = Vx KVL around loop 1

Vx + V4 = V2 + V3 KVL around loop2

V1 + V4 = V2 + V3 KVL around loop3

3. Find out V1 and V2 using KVL.

-20 + v1 + v2 =0 ------------------------(1)

V1 = 2i from the circuit

V2 = 3i

Therefore

-20 + 2i + 3i =0

5i = 20

i=4A

v1 = 2i = 2(4) = 8V

v2 = 3i = 3(4) = 12V

4.Find the current io and voltage vo as shown in the figure using KCL .

At node ‘a’

0.5 io + 3 -io =0

3 – 0.5 io = 0

Io=6A

Vo = 4io

Vo = 4(6) = 24 V

5.Explain nodal analysis ?

Nodal analysis

In the nodal method we are finding the node voltages with the following steps:

- Select a reference node. Assign all the rest nodes voltages , with respect to reference node.
- Use Kirchhoff’s and Ohm’s Laws to each non-reference node and branch currents.
- Resolve the system of equations and obtain node voltages.

Consider the following circuit.

Let us consider a reference node – 3.

In a real circuit a reference node is ground is assumed to have potential.

By the Kirchhoff’s Law having the following current relation:

I1 = i1 + i2

I2 = i2 -i3

Let us represent currents like ratio of voltage and resistance by the Ohm’s Law:

i 1 = v1 /R1 ; i 2 = v1 -v2 /R2 ; i3 = v2/R3;

Or

i 1= v1 * G1 ; i2 =(v1 -v2)*G2 ; i3 =v2 * G3

i1 = v1 * G1 + (v1-v2) * G2 ;

i2 = (v1-v2) * G2 – v2 * G3

i1= v1 * (G1 +G2) – v2 * G2

i2 = v1 *G2 – v2 *(G3 +G2)

Or

And we achieve the following matrix equation, which can be resolved by the Cramer’s rule:

[ G1 + G2 -G3 -G3 ] [v1] = [I1]

[ G2 -G2][v2] =[I2]

Consider the following figure :

There are two possibilities that exist:

- If the voltage source is between reference node and non-reference node, the non-reference voltage is considered equal to the voltage source.
- If the voltage source is between two non-reference nodes, these two nodes are generalised nodes. To determine its voltage Kirchhoff’s Laws must be applied.

Applying Kirchhoff’s Law we achieve the following equations:

i 1 + i4 = i2 + i3

-v2 +5+v3 =0

v 1 =10

By Ohm’s Law

These equations will help determine node voltages.

6. Explain mesh analysis?

Mesh analysis is applicable to the networks which are planar. Planar network is a network where branches are not passing over or under each other.

Nodal method uses Kirchhoff’s currents Law to consider nodal voltages, and Mesh method uses Kirchhoff’s voltages Law to consider mesh currents. Mesh is a loop, which does not contain any other loops.

There are only two meshes in abefa and bcdeb, abcdefa is not a mesh but a loop However, for Mesh method only meshes are in use.

Mesh analysis steps are the following:

- Assign mesh currents to all the meshes in a circuit.
- Apply Kirchhoff’s voltage Law to each mesh. Apply Ohm’s Law to determine voltages with mesh currents.
- To resolve simultaneously all the equations to consider mesh currents.

The following equations correspond to the Kirchhoff’s Voltage Laws for the meshes:

V1 = i1 *(R1+R3) – i2 *R3

-V2 = -i1 *R3 + i2 * (R3 +R2);

[ R1 +R3 -R3 [i1]= [V1]

-R3 R2+R3] [i2] = [V2]

Using Cramer’s formula for resolving the matrix equations above we can find mesh currents.

I1 =i 1 I2 = i2 I1 -I2 =i3

7. Find the current flowing through 20 Ω resistor of the following circuit using Nodal analysis.

Step 1 − There are three principle nodes in the above circuit. Those are labelled as 1, 2, and 3 in the following figure. In the above figure, consider node 3 as reference node (Ground).

Step 2 − The node voltages, V1 and V2, are labelled in the following figure.

Step 3 – There are two nodal equations, since there are two principal nodes, 1 and 2, other than Ground.

The nodal equation at node 1 is

V1 -20/5 + V1/10 + V1-V2/10 =0

2V1 -40 +V1+V1-V2/10 =0

4V1 -40-V2 =0 --- V2 = 4V1-40 -------(1)

The nodal equation at node 2 is

-4 +V2/20 + V2-V1/10 =0

-80 + V2 + 2 V2 – 2V2/ 20 =0

= 3V2 -2V1 =80 --------------(2)

Step 4 − Finding node voltages, V1 and V2 by solving Equation 1 and Equation 2.

Substitute Equation 1 in Equation 2.

3(4V1−40)−2V1=80

⇒12V1−120−2V1=80

⇒10V1=200

⇒V1=20V

Substitute V1 = 20 V in Equation1.

V2=4(20)−40

⇒V2=40V

So, we got the node voltages V1 and V2 as 20 V and 40 V respectively.

Step 5 − The voltage across 20 Ω resistor is nothing but the node voltage V2 and it is equal to 40 V. Now, we can find the current flowing through 20 Ω resistor by using Ohm’s law.

I 20Ω = V2/R

Substitute the values of V2 and R

I 20 Ω = 40/20

I 20Ω = 2A

Therefore, the current flowing through the 20Ω resistor is 2A.

8. Explain series and parallel circuit?

Series and parallel circuit

The basic idea of a “series” connection is that components are connected end-to-end in a line to form a single path through which current can flow:

Series connection

Parallel connection:

The basic idea of a “parallel” connection, on the other hand, is that all components are connected across each other’s leads. In a purely parallel circuit, there are never more than two sets of electrically common points, no matter how many components are connected. There are many paths for current flow, but only one voltage across all components:

Current and voltage division rule

A parallel circuit acts as a current divider as the current divides in all the branches in a parallel circuit, and the voltage remains the same across them. The current division rule determines the current across the circuit impedance. The current division is explained with the help of the circuit shown below:

The current I has been divided into I1 and I2 into two parallel branches with the resistance R1 and R2 and V is the voltage drop across the resistance R1 and R2.

As we know,

V = IR ……..(1)

Then the equation of the current is written as:

I1 = V/R1 and I2 = V /R2

Let the total resistance of the circuit be R and is given by the equation shown below:

R = R1R2/ R1 + R2

Equation (1) can also be written as:

I = V/R ……….(3)

Now, putting the value of R from the equation (2) in the equation (3) we will get

I = V(R1+R2)/ R1R2 ---------------------------(4)

But

V = I1 R1 = I2 R2 ------------------------------(5)

Putting the value of V = I1R1 from the equation (5) in equation (4), we finally get the equation as:

I = I1R1(R1+R2)/ R1R2 = I1(R1+R2)/ R2---------------------(6)

And now considering V = I2R2 the equation will be:

I = I2R2(R1+R2)/ R1R2 = I1/R1 (R1+R2) ------------------------------(7)

Thus, from the equation (6) and (7) the value of the current I1 and I2 respectively is given by the equation below:

I1 + I . R2/ R1 + R2 and I2 = I . R1 / R1 + R2

Thus, in the current division rule, it is said that the current in any of the parallel branches is equal to the ratio of opposite branch resistance to the total resistance, multiplied by the total current.

9. For the following circuit

- Find the total resister value RT
- Find the current i
- Find the voltage over resistors
- Verify Kirchhoff’s voltage law

Solution

RT = 10+20+40+20 = 90 Ω

i = V/RT = (12+6)/ RT = 18/RT = 18/90 =0.2 = 200mA

V1 = 10 x 0.2 = 2V

V2 = 20(0.2) = 4V

V3 = 40x 0.2 = 8V

V4 = 20(0.2) = 4V

V1 + V2 -6 + V3 + V4 -12 =0

2 + 4 – 6 + 8 + 4 -12 =0

10. Explain delta to star conversions.

Delta-star conversions

We know that (from delta to star conversion)

R1 = …….①

R2 = …..②

R1 = ……③

Multiply ① X ② L.H.S and R.H.S

R1 R2 = …….④ where

Similarly, multiply ② X ③

R2 R3 = …….⑤

And ③ X①

R1 R3 = …….⑥

Now add equation ④, ⑤, and ⑥ L.H.S and R.H.S

……refer eq. ②

= + +

= +

Delta to Star Conversion to Find (Req.)

- Equivalent resistance between ① and ②

DeltaStar

= R12// (R23 + R13) =R1 + R2

= = R1 + R2

=

Here let R = R12 + R23 + R13

- Similarly, we can find Req. Between 2 and 3

= R2 + R3

- Similarly, we can find req. Between 1 and 3

R1 + R3

Now the 3 equations after equating L.H.S. And R.H.S

R1 + R2 = …….①

R2 + R3 = ……②

R1 + R3 = …..③

Now subtract ② and ① on L.H.S. And R.H.S

R2+ R3 – R1 – R2 =

R3 – R1 = …..④

Now add equation ④ and ③

R3 – R1 + R1 + R3 =

2R3 =

Similarly, R1 =

And R2 = R23 R12/R where R = R12 + R23 + R13

i.e. star equivalent from delta network is the ratio of the product of adjacent branches in the delta to the addition of all branches in the delta.

11. What is a potential divider?

A potential divider is a simple circuit that uses resisters(or thermistors / LDR’s) to supply a variable potential difference.

They can be used as audio volume controls, to control the temperature in a freezer or monitor changes in light in a room.

Two resistors divide up the potential difference supplied to them from a cell. The proportion of the available p.d. That the two resistors depends on the resistance values.

- Vin = p.d. Supplied by the cell
- Vout = p.d. Across the resistor of interest
- R1 = resistance of resistor of interest R1
- R2= resistance of resistor R2

Example; use the information in the diagram below to find Vout.

Vout = 12x 174/100 +174 = 7.6 V